Jaa Facebookissa Jaa Twitterissä

Tuote 9 / 62
Tämä tuote on lisätty tiistaina 26 heinäkuuta, 2011.

FrSky Futaba FASST yhteensopiva vastaanotin, TFR-SP

Futaba FASST yhteensopiva 10-kanavainen vastaanotin (10ch SUPER EDITION). Yhteensopiva FASST Air lähettimien kanssa: (7CH Mode/Multi Mode)
FrSky: TF-8M, TF-14M
Kantama yli 1,5 km.
Firmware päivitettävissä ja parannettu häiriönsieto.
CPPM moodi Flybarless, FPV tai Trainer käyttöön. Kanavat 1-8 CPPM ulostulo, kanaville 5-10 normi servo ulostulo.

Malli Fr-TFR-SP
Merkki FrSky
Varastossa: 0
Hinta:   €  32,98
Ilman ALV

Futaba FASST yhteensopiva 10 kanavainen vastaanotin (10 ch SUPER EDITION). Mukana tulee englanninkielinen manuaali.

Super mallissa päivitettävä firmware, parannettu häiriönsieto. Nyt 10 kanavainen malli 8 kanavaisten rinnalle!. Kanavat 1-8 CPPM signaalina ulos. Kanaville 5-10 normiservo kanavat. Suunniteltu multikoptereille, FPV lennokeille tai flybarless koptereille, joissa oma lentoaivo ja tällöin voit vähentää johdotusta vastarin ja aivoyksikön välillä.

Yhteensopiva Futaba FASST Air systems (7CH Mode/Multi Mode)
FrSky: TF-8M, TF-14M
Kantama yli 1,5 km

1. Introduction

1.1 Compatibility:

FASST 2.4G: Air Systems (7CH Mode/Multi Mode)
FrSky TF Modules: TF-8M, TF-14M

1.2 Specifications:

Number of Channels: up to 10 channels (CPPM for CH1~CH9, servo signal for CH5~CH10)

With RSSI Output
Operating Voltage Range: 3.5V~10V
Dimension: 53mm*30mm*11mm
Weight: 13.5g


Warning: Servos are not to be plugged into Channel CPPM and Channel RSSI, otherwise servos will get hot or may burn out.
Note: Increased duty means good signal reception, and vice verse.

2.1 Bind procedure:

Turn on the transmitter, connect the battery to the receiver while pressing receiver’s F/S button. After the RED LED is off and GREEN LED is solid, the binding process is completed and the receiver is operating normally.

2.2 Setting failsafe:

TFRSP supports failsafe function for all channels. Follow the steps below to set failsafe:
1) Bind the receiver first, and disable failsafe on the transmitter side;
2) Set all transmitter controls to the desired failsafe position;
3) Press briefly the F/S button of the receiver, the GREEN LED of the receiver will flash twice, indicating the failsafe is set up successfully.
If you do not need the failsafe function any more, just re-bind the receiver to set default failsafe mode.

Warning: Some transmitter manufacturers use a failsafe method that can interfere with that used by FrSky. Be sure to disable any transmitter failsafe settings before setting FrSky failsafe positions. Unusual jitter may result otherwise.

2.3 LED status:

Off On Normal mode
On On Waiting to be bound
Flashing On Signal lost
On Flashing twice Set failsafe


CPPM is usable for reducing wirings to some flybar-less controllers, autopilot systems and homebrew UAV systems. Furthermore, it can be used as a wireless trainer system. 

Please find the how-to guide with the file named “Set up FrSky as a wireless trainer system” via the following link: www.frsky-rc.com/download.asp?id=23